sumitomo减速机,弗兰德减速机,重齿,南高齿-AJ亚洲国际传动设备(上海)有限公司 设为首页 - 加入收藏 - 技术博客 - 网站地图
   齿轮马达
RR系列同轴式斜齿减速机
RS系列斜齿轮-蜗轮减速机
RK系列斜齿-螺旋锥齿轮减速机
RF系列平行轴斜齿减速机
   行星减速机
RP系列行星减速机
   重载齿轮箱
RHB工业齿轮箱
RM系列大型工业减速器
   高速齿轮箱/增速箱
R高速齿轮箱/增速箱
   风电齿轮箱
R风电齿轮箱
   三相异步电动机
R三相异步电动机
您当前位置: 首页 > 新闻资讯
减速机的安装注意事项及操作注意事项

一.安装前的注意事项:

I. precautions before installation:

1. 本机在使用前应对安装轴进行清洗。并检查安装轴是否有碰伤、污物,若有应全部清除干净。

1 the machine should be cleaned before installation. And check whether installation shaft scratches, dirt, if there should be clean.

2.减速机的使用温度为 0~40 ℃。

2 reducer use temperature of 0 ~ 40 C.

3.检查与减速机联接的孔(或轴)的配合尺寸是否符合要求,孔的公差应为H7(轴的公差为H6)。

3 check the connection dimension of the hole (or shaft) connected with the reducer to meet the requirements, the hole tolerance shall be H7 (shaft tolerance is H6).

4.使用前应将最高位处的堵塞换上排气螺塞,保证减速机运行时排出体内气体。

4 before use should be put on the high exhaust plug plug at the discharge gas in the reducer running guarantee.

二.减速机的安装

Two. Installation of speed reducer

1.  减速机只能安装在平的、减震的、抗扭的支撑结构上。

1 reducer can only be installed in flat, shock-absorbing, torsional support structure.

2. 在任何情况下,不允许用锤子将皮带轮、联轴器、小齿轮或链轮等敲入输出轴上,这样会损坏轴承和轴。

2 in any case, do not allow the use of hammer pulleys, couplings, etc. in small gear or sprocket on the output shaft, this will damage the bearing and shaft.

三.使用和维护

Three. Use and maintenance

1. 减速机安装后,检查是否灵活。正式使用请必须进行空载试验,在运转正常的情况下,在逐步加载运转。

1 speed reducer installation, check whether flexible. Formal use must be carried out no-load test, in normal operation, the gradual loading operation.

2.减速机严禁超过额定载荷使用。

2 speed reducer is strictly prohibited than the use of rated load.

3. 减速机在使用前和工作中应检查油位是否正常,本机在出厂前已加注润滑油,润滑油名称:中负荷工业齿

3 reducer before use and work should check the oil level is normal, the machine in the factory before the lubricating oil, lubricating oil in industrial gear load.

轮油 GB5903-86220 。

Round oil GB5903-86220.

四.减速机换油制度:

Four. Speed reducer oil system:

第一次换油   本机运行 300~400小时后应更换润滑油,以后每隔1500~2000小时更换润滑油。在工作环境恶劣、

The first change of the machine running 300 to 400 hours after the lubricating oil should be replaced, after every 1500 ~ 2000 hours to replace oil. In the working environment is bad,

温度高、粉尘大的工作场合下应每隔半个月对润滑油进行一次检查,发现润滑油有污物即更换润滑油,以保持润滑

High temperature, dust under the workplace should be every half a month on the lubricating oil for a check, found that the oil is contaminated with the replacement of lubricating oil to maintain lubrication

油清洁,延长减速机的使用寿命,提高经济效益。

Oil cleaning, extend the service life of reducer, improve economic efficiency.

五.油的更换

Five. Replacement of oil

换油时要等待减速机冷却下来无燃烧危险为止,但仍应保持温热,因为完全冷却后,油的粘度增大,放油困难。

The oil cooling down to wait for the reducer no burning dangerous, but still should keep warm, because completely cooled, oil viscosity, oil discharge difficult.

(注意:要切断传动装置电源,防止无意间通电!)

Note: to cut off the transmission power supply, to prevent inadvertent power! )


日期:2016/12/26 14:18:56
咨询QQ
点击这里给我发消息